Active facade systems · Patent pending

In simulation, a facade that cuts a tower’s perimeter energy by more than half.

Solapane builds electricity generation, energy storage, ventilation, heating and cooling into the curtain wall itself. In hourly simulation of a 30-storey Toronto tower, the perimeter zones behind the facade needed 59% less purchased energy than the same zones behind a conventional curtain wall — with the facade supplying nine-tenths of what heating, cooling and ventilation consume.

One Solapane bay — how it works

PV coverage
Spandrel PV panel Vision glazing transparent PVhigh-performance IGU Mechanical zone PV fasciametal fascia Elevation — from outside 1,600 · 1,600 · 600 mm Outside air Heat rejected outside Conditioned air to the room at floor level outside inside Section — uniform 210 mm depth

The drawing steps through the three PV coverage options. The figures below are for the modelled standard configuration, 370 W of PV per bay, and do not change with it.

59%Less electricity and gas bought from the utility for the perimeter zones than the conventional baseline
82%Less heating energy — and none of it gas
89%Of heating, cooling and fan energy supplied by the facade

PV can be specified in the spandrel alone, in the spandrel and the mechanical fascia, or in all three zones including transparent vision glazing. The mechanical cassette at the floor holds the heat pump, battery and ventilation in every configuration — drawing outside air, rejecting heat outside, and supplying conditioned air to the room through the sill.

The problem

The envelope and the building's systems are fighting each other.

A conventional glass tower lets heat in and out, then spends decades of operating budget countering it with mechanical equipment. Together, the facade and the systems that compensate for it account for roughly a third of construction cost.1

15–25%

of construction cost is the facade alone — the building's largest single surface, and its primary interface with the climate.1

~16%

is mechanical, electrical and plumbing — much of it sized to correct for what the facade lets through.1

~30%

of an office building’s annual operating expense is energy — the largest controllable cost, every year the building stands.2

2,424 MWh

a year to heat, cool and ventilate just the perimeter zones of a 30-storey tower behind a conventional curtain wall — from the simulation below.3

Solapane treats the facade not as a problem to mitigate, but as part of the solution.

What the modelling shows

Simulated, not asserted.

We modelled a 30-storey, 25,000 sq ft-per-floor reference tower in EnergyPlus — full 8,760-hour annual runs against a Toronto weather file — comparing Solapane against a conventional double-glazed curtain wall with gas-fired perimeter heating. The accounting covers the perimeter zones — the 4.6 m-deep strip behind the facade on every floor — and includes their lighting and plug loads on both sides, so the percentage is what those zones draw from the meter.

Annual, perimeter zones (MWh)BasisConventional baselineSolapane
HeatingGas boiler / cassette heat pump with resistance backup914 gas162
CoolingDX, COP 3.0 in both cases723599
FansSupply fans, occupied-continuous / cycling787504
Interior lighting8 W/m², office schedule622622
Plug loads7.5 W/m², office schedule809809
Facade PV generatedGross annual output, 370 W per bay—1,212
Of which used on siteMet load hour by hour, through the cassette batteries; surplus not credited—−1,121
Purchased energy3,8551,575  (−59%)

Where the reduction comes from

Three effects compound. The envelope cuts the load: heating energy falls 82% and fan energy 36%. Heat-pump conditioning meets that load without gas. And facade generation with on-cassette storage supplies 1,121 MWh on site — 89% of what heating, cooling and ventilation consume. Lighting and plug loads are untouched; they are the floor a building cannot go below without changing how it is used.

What we deliberately left out

The model excludes any improvement in heat-pump efficiency from the facade cavity. Tropical-climate runs against a Bangkok weather file are complete; results are available under NDA.

These are simulation results produced in-house. Independent third-party testing of a full working facade unit is the next milestone, and no performance claim should be treated as validated until that testing is complete.

The approach

An active facade, not a passive one.

For decades the facade has been a barrier, and the building has spent energy compensating for its limits. Solapane reverses that relationship: the envelope becomes an active contributor to energy performance, comfort and resilience.

Lower operating energy

Cuts what a commercial building spends keeping occupants comfortable, moving the envelope toward net-zero performance rather than merely slowing losses.

Comfort and air quality

A warmer, more stable interior surface and better air at the perimeter — where cold downdraft and glare are the daily complaints, and where people actually sit.

Cold climate by design

Engineered in Canada for northern winters, where conventional building systems lose both efficiency and comfort exactly when they are needed most.

New build and retrofit

Built on decades of unitized curtain-wall manufacturing — for new towers, and for the large stock of aging commercial facades due for replacement.

Every climate

Two models. One platform.

Buildings face the climate differently in Toronto than in Singapore. Solapane meets that with two configurations of the same active-facade platform, so the system fits the market rather than the other way around.

The Climate Model

Full heating and cooling across the year, for markets where buildings must do both. The flagship configuration, engineered for northern winters and four-season climates alike.

Canada · United States · Europe · East Asia

The Cooling Model

A cooling-focused configuration for hot and tropical regions, where managing solar load is the year-round challenge and heating capacity would sit idle.

Middle East · South Asia · Southeast Asia · Australia

Why it matters

A Canadian innovation, built for the world.

Designed for the hardest case

Engineered first for Canadian winters, where building systems are pushed hardest. A system that performs there is built to perform anywhere.

Aging building stock

Most Canadian commercial buildings predate modern envelope standards. Solapane is designed for retrofit, not only for new construction.

Decarbonization at the source

Cuts carbon at the building itself, supporting net-zero targets without waiting on grid expansion or new generation capacity.

Canadian intellectual property

U.S. provisional application filed July 2026, with PCT filing to follow. Owned by RZG Technologies, developed in British Columbia.

Where we are

Credibility before scale.

Solapane is in active development and pre-revenue, with foundational intellectual property filed. The path is deliberate: prove the system and earn independent validation before any broad commercial push.

Today — design and IP

Engineering underway

Design concept complete, hourly energy simulation done. Provisional patent filed July 2026; PCT to follow within twelve months. First reference-building candidates identified in Vancouver.

Next — prototype

Independent validation

Build a full working facade unit and confirm its performance through independent, third-party testing rather than in-house modelling alone.

Then — pilot

First installation

A live building, with a full annual cycle of real-world performance data standing as the commercial reference.

The company

RZG Technologies Inc.

A British Columbia clean-technology company developing advanced facade and envelope systems.

Solapane is led by Robert Grandbois, a mechanical engineer with more than 45 years across HVAC and high-performance curtain-wall systems. In 1985 he and two partners licensed the Visionwall high-performance envelope system; their company delivered its first projects in 1987 and opened its Edmonton manufacturing plant in 1989 — a four-decade record of taking advanced facade technology from licence through to production.

That history is the reason Solapane starts from manufacturability rather than from a laboratory prototype. The system is designed around unitized curtain-wall production methods that already exist at scale.

Headquarters
Coquitlam, British Columbia
Sector
Clean technology · building envelope
Stage
Pre-commercial R&D, pre-revenue
Intellectual property
U.S. provisional filed July 2026 · PCT to follow
Founder
Robert Grandbois, BSc Mechanical Engineering

Notes and sources

  1. Facade at 15–25% of total construction cost: Kragh, Building Envelopes and Environmental Systems, CIBSE. Mechanical, electrical and plumbing at roughly 16%: UK commercial-office cost models published by Building. The two are separate figures, summed here to describe the combined cost of the envelope and the equipment that compensates for it.
  2. Energy as roughly 30% of commercial office operating expense and the largest controllable cost: ENERGY STAR, commercial real estate. Space heating, cooling and ventilation are the largest end uses within that energy (U.S. EIA, CBECS); their share of operating cost is not stated here because it depends on fuel mix and tariffs.
  3. Baseline heating (914 MWh of gas), cooling (723 MWh) and fans (787 MWh) for the perimeter zones of the 30-storey, 750,000 sq ft (about 70,000 m²) reference tower, from the simulation described in note 4. A modelled figure, not a measured result from a specific building.
  4. Energy figures throughout are outputs of in-house EnergyPlus 26.1 simulations (variant A-370): 8,760-hour annual runs, Toronto CWEC2016 weather file, 30-storey reference tower with a 25,000 sq ft floor plate, with the four perimeter zones (4.57 m deep, about 24,200 m² over 30 floors, roughly 35% of floor area) modelled and the core treated as adiabatic. The baseline is a conventional double-glazed curtain wall — vision glazing U 2.0 W/m²K, SHGC 0.40, the same insulated spandrel without PV — representative of code-minimum envelope performance under the National Energy Code of Canada for Buildings, with packaged DX cooling and gas-fired perimeter heating. Cooling is modelled at COP 3.0, lighting at 8 W/m² and plug loads at 7.5 W/m² on an office schedule in both cases. Purchased energy is EnergyPlus’s hourly Electricity Coming From Utility (plus natural gas for the baseline), not an annual subtraction: facade PV output is applied to load hour by hour through the cassette batteries. Of 1,212 MWh generated in the standard configuration, 1,121 MWh met on-site load; the remaining 91 MWh was surplus to demand at the time it was produced, or lost in storage, and is not credited. All percentages are energy, not utility cost; cost savings depend on tariffs, demand charges and export treatment. Results are unvalidated by third parties and are presented as modelled performance, not measured performance.
Get in touch

Let's talk about your building.

We're engaging building owners, institutional partners and government programs, and sharing full technical detail with qualified parties under NDA.

info@solapane.com

No securities offering is currently being made. Interested parties are invited to register interest under NDA; detailed materials follow upon qualification.